![]() Only engage the Thunderbolt locks while the van is not occupied. If the Thunderbolt M2 locks are used, the locks should not be engaged while driving. NOTE: When operating the locks from the factory key fob, the M1+ locks with built-in lock inhibitors should be used where a passenger may be riding to prevent the lock from engaging while the van is driving for safety. BEVISKkki 2 Pack Hidden Shackle Padlock Heavy Duty Solid Steel Cargo Van Door Locks Anti Theft with Hasp 73MM Puck Lock High Security Garage Shed Door Lock with 4 Keys for Trucks, Gates, Vans,Trailer. When installing locks in front doors ensure that no part of the lock interferes with the window rolling down. The Chevy Express cab doors have a wider gap to span, requiring a raised strike bracket accessory. Depending if your doors already have a factory boot to run wires into the door, you may or may not need a contact switch.Ĭab door locks get installed inside the door, and the deadbolt engages into the mating B pillar. If you are installing the lock in swing doors, the lock should be installed in the door closest to the front of the van. If you use an M2 model lock, install the provided contact switch to bring power into the door. If you plan to operate your Thunderbolts from your factory remote, connect the wires to the factory lock wires. When installing a deadbolt lock in a side sliding door, it gets installed on the side towards the rear of the van, and the bolt strikes into the rear C pillar. At the very least, you can use a high-quality thick gauge loom to protect the wires. Needs the factory boot, we recommend purchasing one from the manufacturer. When routing wires outside a door, they should be routed through a door factory boot to protect the wires. A raised strike bracket is NOT required on the rear Chevy Express door. The lock should be installed inside the rear “passenger-side” door and have the bolt strikes into the opposing door. If you are not confident performing the installation or are unfamiliar with locating or connecting wires, we highly recommend hiring a professional. ![]() Then follow the installation guide with the steps outlined. Van Locks Van Roof Bars Van Roof Racks Pipe Carriers. accountcircle Register / Log In search phone UK Order Line 01392 368351 Toggle navigation. Range includes Deadlocks, Slamlocks, Hooklocks & more. (4) M2 Locks (one for each door) (includes two pre-programmed Thunderbolt key fobs)īegin with watching the general installation video and any supporting videos, and review photos of prior installations. Our latest line of Van Security products. (1) Distribution Block (connects to the battery, then each lock gets wired into the block) Not required but highly recommended. (2) M2 Locks (includes two pre-programmed Thunderbolt key fobs) ![]() Operated locks from a Thunderbolt Key Fob: (1) Keyed Manual Release (in case of battery failure) Installed in cab door. (2) M1 Locks (rear swing and side sliding doors) (2) M1+ Locks (cab doors with built-in lock inhibitors) Please contact us for more information.Operated locks from your Factory Key Fob:Ĭhevy Express 2-Door Security (rear swing and side sliding doors)Ĭhevy Express 4-Door Security (cab doors, rear swing, and side sliding doors) a CR Laurence window) then this lock may not fit your sliding door above the rail. PLEASE NOTE if you have an aftermarket window installed in the sliding door (I.E. You can trust Tufloc to have a high-security door lock to meet your needs no matter your situation.Grease the holes and put the sponge rubber seal in place.Tools needed for install- 3.2 mm drill bit (now included) to drill pilot holes, 4mm Allen key to tighten screws! DO NOT USE an impact drill or anything other than an Allen key to tighten screws.For the rear wing doors, the lock is mounted on the door that has the latch to open from the inside.Please check before the drilling that the door passes the lock without any difficulties. Please pay attention to the sliding door: the lock should be position about 10 cm above the rail.The best way to do this is by holding the frame at the position where you want to mount the lock. In this position, the key can't be removed. Only in the locked or unlocked position, the key can be removed.ĪSSEMBLY INSTRUCTIONS - Unlock the VAN security lock and turn it 90°.Unlock the VAN security lock with the key and turn it 180° so that you can open the door. ![]() ![]() The lock can only be engaged with the key.Will fit on most sliding, wing and rear doors on vans. Swivel locks to secure the sliding, wing and rear doors. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |